Below we’ve highlighted 15 of the most common types of car sensors that you can find in almost any new vehicle. Not only did we highlight what they are, but we also gave each one a brief description and highlighted how they work.
1. Engine Oil Level Sensor
One of the most common sensors in your vehicle is the engine oil level sensor. This sensor measures the oil level in your engine oil pan to ensure that it’s at a safe operating capacity. If you don’t have enough oil, this sensor will cause an oil level warning light on your dashboard.
This sensor is often installed on the bottom of the oil pan, so you need to tap out the engine oil to replace it. This depends on the engine model, though.
2. Engine Oil Pressure Sensor
The engine oil pressure sensor is often quite similar to the oil level sensor, except that it measures the oil pressure after the oil pump. You will often find this sensor located at the engine block, often near the fuel filter.
The engine oil pressure sensor often has some plastic parts that can crack with age, which can cause it to start leaking before it malfunctions. You will mostly notice a bad oil pressure sensor by seeing a red oil pressure light on your dashboard.
3. Coolant Temperature Sensors
Another critical sensor in your engine is the coolant temperature sensor. This sensor monitors your coolant temperature, which is a great way to determine your engine’s overall temperature. If it gets too hot, engine damage can occur.
In some newer car models, the coolant temperature should shut off your engine once it reaches a high enough temperature.
4. Mass Airflow Sensor
Your vehicle’s engine needs to know how much air is coming in so it can optimize the fuel ratio for maximum performance. Your mass airflow sensor (MAF) measures the amount of air coming through the intake, so it knows how much it’s bringing in.
The MAF sensor is often located on the intake hose between your intake manifold and the air filter box.
5. Intake Air Temperature Sensor
Believe it or not, the air temperature coming into the engine is a critical part of maximizing engine performance. That’s why the intake air temperature sensor (IAT) tells the ECM the air temperature, so it makes adjustments and maximizes performance.
The IAT sensor can either be separate or integrated into the MAF Sensor. Integrated into the MAF sensor is far more common on newer car models.
6. Oxygen Sensors
Oxygen sensors, also known as O2 sensors, measure your air-fuel mixture from the exhaust and the catalytic converter’s effectiveness (CAT). One oxygen sensor measures the air’s makeup before the CAT, and one measures the makeup of the air after the CAT
If there’s not enough of a drop in emissions, it lets the ECM know that you need to make repairs by showing a check engine light on your dashboard.
7. Knock Sensors
Knock sensors are there to make sure that your engine will not suffer from detonation or so-called knocking. Detonation or knock in a car engine is fatal for the internal parts, resulting in a very costly repair.
This could also be from misfires or broken components, but if your engine’s knock sensor hears something – you have a problem.
8. Crankshaft/Camshaft Position Sensors
Engine timing relies on a perfect symphony between the crankshaft and camshaft – and their respective position sensors let the ECM know precisely where each one is at. If those positions don’t line up to what they should be, you need to know as soon as possible.
You do often have one sensor on the camshaft and one on the crankshaft. Some car models do only have a crankshaft position sensor, though.
9. Throttle Position Sensor
Nowadays, the connection between the accelerator pedal and the throttle body is fully connected by electronics instead of a cable. Therefore, on the throttle body, there is a throttle position sensor to measure the throttle flap’s angle.
The throttle position sensor tells the ECM exactly how open the throttle is. That way, if there’s a problem between the pedal and the throttle, it won’t dump a ton of fuel in and damage the engine because of a sticky throttle.
10. Manifold Absolute Pressure Sensor
Your manifold absolute pressure sensor (MAP) sensor does exactly what it sounds like it would do – it measures pressure in the manifold. This takes your mass airflow sensor one step further by measuring how much air is actually making it to your engine. This is a critical component in fuel-injected engines as it optimizes your fuel ratios for the best possible performance.
It also takes the job from the boost pressure sensor and measures the turbo pressure, if your car is equipped with one.
11. Fuel Pressure Sensor
The fuel pressure sensor measures the fuel pressure on your fuel pressure line or at the fuel pressure rail. It is most likely to be mounted on your fuel pressure rail, but sometimes it can also be mounted on the fuel pressure line. It is critical for the engine control module to measure the fuel pressure, as an increase in pressure would result in a richer fuel mixture, and a lower pressure would result in a leaner fuel mixture.
The sensor itself is often quite cheap, but it can be unwieldy to replace it if you are not an experienced mechanic. (A lot of fuel may leak out).
12. Coolant Level Sensor
If your vehicle doesn’t have enough coolant, it’s going to overheat. That’s why most vehicles come with a coolant level sensor, that way, you can avoid problems before you hit the road. If your vehicle doesn’t have enough coolant, then the coolant level sensor will light up the check engine light – and sometimes it will keep you from starting your vehicle.
The coolant level sensor is located on your coolant reservoir.
13. Nox Sensor
The Nox sensor measures the Nox volume in the exhaust gases. This sensor is not installed in many car models. Typically you can find them at Volkswagen, Audi, Seat, and Skoda. The Nox sensor is installed on the exhaust pipe and the control unit under a plastic cover.
To replace the NOX sensor, you do often have to replace the control unit for it also, unfortunately. The control unit and the sensor are often costly, and the replacement can be a bit tricky because the sensor tends to rust and get stuck.
14. Exhaust temperature sensor
The exhaust temperature sensor is often installed in diesel engines. Its purpose is to measure the exhaust gas temperature before and after the particle filter to optimize particle filter regeneration. Depending on the vehicle engine model, you often have 1 to 4 exhaust gas temperature sensors.
The sensors are installed on the exhaust pipe and the exhaust manifold, and sometimes also on the turbocharger. The sensors are often quite expensive and can be difficult to reach and replace; they often rust and get stuck.
15. Boost pressure sensor
The boost pressure sensor measures the boost pressure in the intake boost pipes. You do only have this sensor if your car is equipped with a turbo or supercharger.
The boost pressure sensors are often cheap and can be easily replaced on most car models. Some car models can be difficult to access if they are mounted on the intake manifold.
Tags:
Tips